In order to give you better service we use cookies. By continuing to browse the site you are agreeing to our use of cookies.
sonarworks.png

Remove unwanted coloration from studio speakers and headphones.

 

Focus on the music instead of worrying about your setup

and make the right impact on every listener out there.

 

Check the short introduction video by clicking the link below 

Introduction video

Filter & sort
Number of articles 11
Sort
Reference 4 Studio edition with mic - boxed
SNW-SW4SXLR

Finally you can work with confidence on the setup you have. Sonarworks Reference 4 removes unwanted coloration from your studio speakers and headphones, so you can trust that you hear your mix accurately.

Reference 4 Studio Edition offers the full package of highly powerful software, providing consistent reference sound, both in the studio and on the go. You can also measure your studio with the included mic, in only 10 minutes. Reference 4 then creates a calibration profile. For headphones, select a pre-made profile and you're ready to go. Calibration can be run in DAW via plugin for lowest latency or via Systemwide for maximum versatility.

 

Reference 4 Studio Edition includes:

Reference 4 Measure - find out where your monitors need help

Reference 4 DAW plugin - reference sound combined with zero latency for any musical endeavor

Reference 4 Systemwide - apply calibration to all outgoing audio

XREF20 measurement mic - sniffs out any faults your setup might have

All products can be activated on 3 machines.

 

System requirements:

Mac: macOS 10.9 or later

PC: Windows 7 or later

Hardware: 2 GB RAM; 1024x768 display

Measurement microphone with a flat frequency response

Audio interface with phantom power (for XLR microphones) Sonarworks supported headphones or Sonarworks individually calibrated headphones

 

NB: Currently our speaker measurement software Reference 4 Measure does not work on Windows 10 with Thunderbolt Apollo and Avid HD interfaces.

 

Reference 4 - Step by Step Tutorial

Measurement Microphone for Recording Studios (XREF20)
SNW-XREF20R4

Sonarworks XREF20 is also the best way to try Reference 4 speaker calibration. Included is a 21 day FREE trial that will give you plenty of time to finally hear how your setup sounds without room induced coloration. Focus on the music, instead of worrying about your gear!

At this price range, all measurement microphones are roughly the same, so what makes the XREF20 stand out is its individual calibration profile. Every mic has been measured by Sonarworks acousticians against an ANSI certified measurement microphone. This means perfect accuracy within the audible range and freedom from sample-to-sample irregularities.

 

This package includes:

Professional measurement microphone with XLR connection (requires 48V phantom power)

Individual off-axis calibration curve for best results with Sonarworks software Individual 0° calibration curve

21-day trial version of Sonarworks Reference 4 Studio Edition (Mac or Win)

 

Microphone specification:

XLR connection with 48V phantom power required

Houses pre-polarized electret-condenser capsule

Frequency response: 20 Hz - 20kHz with supplied calibration profile Omnidirectional polar pattern

Sensitivity is rated at -37dB/Pa (14 mV)

Self noise: 24 dB

S/N ratio: 70 dB

Dynamic range: 106dB

Maximum SPL: 132 dB SPL

 

NB: Currently our speaker measurement software Reference 4 Measure does not work on Windows 10 with Thunderbolt Apollo and Avid HD interfaces.

Reference 4 Premium Bundle with HD-650
SNW-SW4SHD650

Sennheiser HD 650 Headphones + Reference 4 Studio Edition

Reference 4 Studio Edition offers the full package of highly powerful software, providing consistent reference sound both in the studio and on the go. Measure your studio with the included mic, it takes around 10 minutes. Reference 4 then creates a calibration profile. For headphones select a pre-made profile, and you're ready to go. Calibration can be run in DAW via plugin for lowest latency or via Systemwide for maximum versatility.

Pre-Calibrated Sennheiser HD 650 Headphones together with Reference 4 brings you sonic accuracy, unattainable by hardware alone. Uniquely advanced filter engine allows Sonarworks to correct all FR dips and peaks, making these headphones perfect for monitoring, on-site duties as well as record mastering. Each of these use scenarios have a corresponding filter setting. Minimum phase when no latency is paramount, linear phase for extreme accuracy and a golden middle setting - mixed phase.

Reference 4 Headphone edition - download
SNW-SW4HD

Sonarworks Reference 4 removes unwanted coloration from your headphones, so you can trust that you hear your mix accurately. Bring reference sound wherever. Finally be confident that the music you create or edit will sound good wherever it's played.

Reference 4 Headphone Edition is crafted specially for sound creatives who rely on headphones for monitoring. Calibration makes headphones fit for even the most demanding applications, like mastering, with only a few button clicks.

 

Reference 4 Headphone Edition includes:

DAW plugin (AU, VST, RTAS, AAX)

Systemwide which corrects all outgoing audio

All products can be activated on 3 machines.

 

System requirements:

Mac: macOS 10.9 or later

PC: Windows 7 or later

Hardware: 2 GB RAM; 1024x768 display

Sonarworks supported headphones or Sonarworks individually calibrated headphones

  

How to Mix Better in Headphones

SNW-SW4HB

Sonarworks Reference 4 removes unwanted coloration from your headphones, so you can trust that you hear your mix accurately. Bring reference sound wherever. Finally be confident that the music you create or edit will sound good wherever it's played.

Reference 4 Headphone Edition is crafted specially for sound creatives who rely on headphones for monitoring. Calibration makes headphones fit for even the most demanding applications, like mastering, with only a few button clicks.

 

Reference 4 Headphone Edition includes:

DAW plugin (AU, VST, RTAS, AAX)

Systemwide which corrects all outgoing audio

All products can be activated on 3 machines.

 

System requirements:

Mac: macOS 10.9 or later

PC: Windows 7 or later

Hardware: 2 GB RAM; 1024x768 display

Sonarworks supported headphones or Sonarworks individually calibrated headphones

 

How to Mix Better in Headphones

 

Reference 4 Studio edition - download
SNW-SW4SD

Finally you can work with confidence on the setup you have. Sonarworks Reference 4 removes unwanted coloration from your studio speakers and headphones, so you can trust that you hear your mix accurately.

Reference 4 Studio Edition offers the full package of highly powerful software, providing consistent reference sound both in the studio and on the go. Measure your studio with a measurement mic, it takes around 10 minutes. Reference 4 then creates a calibration profile. For headphones select a pre-made profile, and you're ready to go. Calibration can be run in DAW via plugin for lowest latency or via Systemwide for maximum versatility.

 

Reference 4 Studio Edition includes:

Speaker measurement software - find out where your monitors need help

DAW plugin - reference sound combined with zero latency for any musical endeavor

Systemwide - apply calibration to all outgoing audio

After you purchase the licence, an activation key will be sent to you. All products can be activated on 3 machines.

 

System requirements:

Mac: macOS 10.9 or later

PC: Windows 7 or later

Hardware: 2 GB RAM; 1024x768 display

Measurement microphone with a flat frequency response (not included)

Audio interface with phantom power (for XLR microphones) (not included)

Sonarworks supported headphones or Sonarworks individually calibrated headphones

 

NB: Currently our speaker measurement software Reference 4 Measure does not work on Windows 10 with Thunderbolt Apollo and Avid HD interfaces.

 

Reference 4 - Step by Step Tutorial

SNW-SW4SB

Finally you can work with confidence on the setup you have. Sonarworks Reference 4 removes unwanted coloration from your studio speakers and headphones, so you can trust that you hear your mix accurately.

Reference 4 Studio Edition offers the full package of highly powerful software, providing consistent reference sound both in the studio and on the go. Measure your studio with a measurement mic, it takes around 10 minutes. Reference 4 then creates a calibration profile. For headphones select a pre-made profile, and you're ready to go. Calibration can be run in DAW via plugin for lowest latency or via Systemwide for maximum versatility.

 

Reference 4 Studio Edition includes:

Speaker measurement software - find out where your monitors need help

DAW plugin - reference sound combined with zero latency for any musical endeavor

Systemwide - apply calibration to all outgoing audio

After you purchase the licence, an activation key will be sent to you. All products can be activated on 3 machines.

 

System requirements:

Mac: macOS 10.9 or later

PC: Windows 7 or later

Hardware: 2 GB RAM; 1024x768 display

Measurement microphone with a flat frequency response (not included)

Audio interface with phantom power (for XLR microphones) (not included)

Sonarworks supported headphones or Sonarworks individually calibrated headphones

 

NB: Currently our speaker measurement software Reference 4 Measure does not work on Windows 10 with Thunderbolt Apollo and Avid HD interfaces.

UPGRADE Reference 3 to Reference 4 - download
SNW-SW4U3D

Reference 4 introduces zero latency processing and makes sure you get the latest developments in DSP-assisted monitoring.

 

After buying you will get all the info you need to set up Reference 4. All of your old profiles will work, so you can pick up right where you were. Your machine must have at least macOS 10.9 or Windows 7.

 

NB: After the release of Reference 4, no new features will be added to any of the older versions. Expect Reference 3 patches only to fix critical bugs.

UPGRADE Reference 3 to Reference 4 - boxed
SNW-SW4U3B

Reference 4 introduces zero latency processing and makes sure you get the latest developments in DSP-assisted monitoring.

 

After buying you will get all the info you need to set up Reference 4. All of your old profiles will work, so you can pick up right where you were. Your machine must have at least macOS 10.9 or Windows 7.

 

NB: After the release of Reference 4, no new features will be added to any of the older versions. Expect Reference 3 patches only to fix critical bugs.

UPGRADE Headphone to Studio edition - download
SNW-SW4UHD

Unify all of your monitoring devices under the same reference sound and work with confidence both in studio and on-the-go.

 

Upgrade to Sonarworks Reference 4 Studio Edition adds speaker calibration to the already impressive set of features of Headphone Edition.

  

System requirements remain the same, however you'll need a 48V phantom power capable audio interface to do the measurements and a calibrated measurement microphone. If you don't have such a mic, our Measurement Microphone for Recording Studios (XREF20) is your best option.

  

NB: Currently our speaker measurement software Reference 4 Measure does not work on Windows 10 with Thunderbolt Apollo and Avid HD interfaces.

 

 

UPGRADE Headphone to Studio edition - boxed
SNW-SW4UHB

Unify all of your monitoring devices under the same reference sound and work with confidence both in studio and on-the-go.

  

Upgrade to Sonarworks Reference 4 Studio Edition adds speaker calibration to the already impressive set of features of Headphone Edition.

  

System requirements remain the same, however you'll need a 48V phantom power capable audio interface to do the measurements and a calibrated measurement microphone. If you don't have such a mic, our Measurement Microphone for Recording Studios (XREF20) is your best option. 

 

NB: Currently our speaker measurement software Reference 4 Measure does not work on Windows 10 with Thunderbolt Apollo and Avid HD interfaces.

The product has been added to your shopping cart Show shopping cartCheckout